Strong starter alternator installation Ursus C330

PREMIUM set - REINFORCED Starter + Alternator + Installation for URSUS C-330 tractors SKRAW-MET CODE: [7364] This is a set dedicated to URSUS C-330 agricultural machines.

The set includes: Reinforced starter with C-330 C-360 reducer ZETOR URSUS 12V 2.8kW 11z [2563]

Alternator Ursus C-330 14v 45A [2511]

Electrical installation Ursus C-330 [2539]

Complete set ready for work. The elements used in the set guarantee long and reliable operation.

ENHANCED STARTER FOR URSUS ZETOR 12V 2.8kW machines (11 teeth) SKRAW-MET CODE: [2563] ENHANCED VERSION It is characterized by higher power and at the same time lower power consumption and an additional cover for the automatic machine (electromagnet).

High-speed starter of the 2nd generation with a reducer facilitating starting engine at low temperatures.

With a built-in planetary gear (reducer) on bearings - thanks to lower battery power consumption - it will start at ANY TEMPERATURE.

The dynamoelectric structure is made with particular care - only from high-quality materials, thanks to modern technology and quality control we guarantee a durable and reliable starter.

It is a complete starter dedicated to ZETOR, URSUS C-330, C-360, C-330M, C-335 and similar agricultural machines. It includes:

head and cap,

brushes

stator (winding)

rotor

machine with forks

machine cover

bendix

gear (reducer)

set of bearings

NON-REGENERATED STARTER - BRAND NEW​

Technical specifications: Power: 2.8 kW

Rated voltage: 12 V

Number of teeth on the bendix: 11 z

Rated rotational speed at 20.5 Nm: 1500 rpm

Current consumption during idle operation: 160 A

Current consumption during full overload: 720 A

Hole spacing: 127x90x90mm

Holes: 10.5 mm

For proper operation - do not connect a voltage higher than 16.5 V, and the operating time cannot be longer than 3 × 20 seconds. The preventive interval between starting the starter cannot be shorter than 30 seconds - otherwise it may overheat. ALTERNATOR C-330 14V 45AKOD SKRAW-MET: [2511]The alternator is a source of electrical energy, intended to work in parallel with the battery of the electrical installation of agricultural vehicles/machines. It is used to charge the battery.

It is a complete alternator dedicated to URSUS 328, C-330, C-330M, C-335 agricultural machines. It includes:

housing,

pulley with a fan,

stator (winding)

rotor

voltage regulator,

brushes

set of bearings

set of elements to be attached with a sleeve.

Technical specification: Internal spacing of mounting holes from the eye to ear (on the right side of the photo): 88 mm

Outer spacing of mounting holes from ear to ear (on the right side of the photo): 108 mm

Spacing from left ear to right: 142 mm

Length of ear sleeve: 45 mm

Rated voltage : 14 V

Rated current: 45 A

Rated rotational speed: 2500 rpm

Maximum rotational speed: 6000 rpm

Pulley: single

Proper operation of the alternator is expected at an ambient temperature of -40°C to +45° C and humidity 90%.

Alternator installation: Attention! Before installing the alternator, disconnect the battery in the system. When installing the alternator, you should:

Remove any preservatives from the alternator using rags moistened with gasoline and dry,

Install the alternator on the engine bracket without completely tightening the bolts securing it to the block Install the drive belt on the alternator pulley and adjust its tension Place the alternator in the optimal position and tighten the mounting bolts Connect the wires to the alternator in accordance with the vehicle electrical installation diagram Connect the battery terminals and start the vehicle.

The place where the power cable should be connected is marked in red, the output to the control lamp is marked in blue. Note! Poor belt tension leads to reduced power delivered by the alternator and to undercharging of the battery. Excessive belt tension leads to significant overheating of the alternator bearings and their premature failure.

Attention! Installation of the belt on the alternator pulley should be done without using tools with sharp edges.

Set of electrical installation for URSUS C-330 SKRAW-MET CODE: [2539] POLISH product - high quality! Dedicated installation for URSUS C-330 agricultural tractors.

It can be used in agriculture, horticulture, forestry, construction and the broadly understood industry.

All elements are made only of durable, high-quality plastics.

The installation is adapted to the alternator available in our other auctions. The electrical installation is based on high-quality cables. The set includes: a set of cables

ignition switch with key

fuse box

turn signal switch

All components in the set (i.e. ignition switch or switch) are already connected to the cables. Note! The installation does not contain fuses!